- 您现在的位置：买卖IC网 > Sheet目录1228 > MAX5976BEVKIT+ (Maxim Integrated Products)EVAL KIT MAX5976B
2.7V to 18V, 7A, Hot-Swap Solution
Power-Good Delay
The devices feature an open-drain, power-good output
that asserts after 16ms (typ), indicating that OUT has
devices' internal switch goes into normal operation. Use
the following equation to calculate the resistors values for
the desired undervoltage threshold:
V IN
? V
- 1 ? × R2
?
reached (0.9 x V IN ) voltage.
REG
The devices include a linear regulator that outputs
?
R1 = ?
? ON1_TH
?
?
I LIMIT (A) = ? ? × R CB ( ? )
2.6V at REG. REG provides power to the internal circuit
blocks of the ICs and must not be loaded externally. REG
requires a 1 F F capacitor to ground for proper operation.
Fault Status Output ( FAULT )
FAULT is an open-drain output that pulls low when a cur-
rent limit or an overtemperature fault shutdown occurs.
FAULT remains low until the next startup cycle. FAULT is
capable of sinking up to 5mA when asserted.
Thermal Protection
The devices enter a thermal shutdown mode in the event
of overheating caused by excessive power dissipation
or high ambient temperature. When the junction tem-
perature exceeds T J = +150 N C (typ), the internal thermal
protection circuitry turns off the internal power MOSFET.
The devices recover from thermal shutdown mode once
the junction temperature drops by 20 N C (typ).
Applications Information
Setting the Undervoltage Threshold
The devices feature an independent ON/OFF control
(ON1) for the internal MOSFET. The devices operate
with a 2.7V to 18V input voltage range and has a default
2.5V (typ) undervoltage lockout threshold. The internal
MOSFET remains off as long as V IN < 2.5V and/or V ON1
< V ON1_TH . The undervoltage lockout threshold is pro-
grammabl e using a resistive divider between ON1 and
GND (Figure 1). When V IN is greater than 2.7V and V ON1
exceeds the 1.21V (typ) threshold, the gate of the inter-
nal MOSFET enhances to 5V, with respect to V IN and the
where V IN is the desired turn-on voltage for the output
and V ON1 is 1.21V. R1 and R2 create a resistive divider
from V IN to ON1. During normal operating conditions,
V ON1 must remain above its 1.21V (typ) threshold. If
V ON1 falls 100mV (V ON1_HYS ) below the threshold, the
internal MOSFET turns off, disconnecting the load from
the input.
Setting the Current Limit
An external resistor from CB to ground sets the current
limit for the devices. Use the following formula to set the
current limit:
? 0.175A ?
? 1000 ? ?
Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns,
go to www.maxim-ic.com/packages . Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package
drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE PACKAGE OUTLINE LAND
TYPE
16 TQFN-EP
CODE
T1655+3
NO.
PATTERN NO.
8
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX5977AEVKIT#
EVAL KIT MAX5977A
MAX5980EVKIT#
EVAL KIT MAX5980
MAX5982CEVKIT#
EVAL KIT MAX5982C
MAX6397SATA+T
IC SW OVERVOLT PROT 8-TDFN
MAX6496EVKIT+
KIT EVAL FOR MAX6496
MAX6651EVKIT
EVAL KIT FOR MAX6651
MAX7325EVKIT+
KIT EVAL FOR MAX7325
MAX7326EVKIT+
KIT EVAL FOR MAX7326
相关代理商/技术参数
MAX5977AETP+
功能描述:热插拔功率分布 1-16V Hot-Swap Controller
RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977AETP+T
功能描述:热插拔功率分布 1-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977AEVKIT#
功能描述:热插拔功率分布 MAX5977A Eval Kit RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977AEVKIT+
功能描述:热插拔功率分布 1V to 16V Hotswap Controller with Precision Current Sensing Output RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977BETP+
功能描述:热插拔功率分布 1-16V Hot-Swap Controller
RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977BETP+T
功能描述:热插拔功率分布 1-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977ETP+
制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX5978ETJ+
功能描述:热插拔功率分布 0-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube